Aftermarket Engines Mitchell SD

This page provides relevant content and local businesses that can help with your search for information on Aftermarket Engines. You will find informative articles about Aftermarket Engines, including "Build With Bolt-On Horsepower, But Proceed With Caution". Below you will also find local businesses that may provide the products or services you are looking for. Please scroll down to find the local resources in Mitchell, SD that can help answer your questions about Aftermarket Engines.

Campbell Supply of Mitchell
(605) 996-8305
1400 S Burr Street
Mitchell, SD
Services
Veterinary Equipment & Supplies, Auto Service & Repair, Auto Parts Retail, Hardware Dealers
Products
Service

Carquest of Mitchell
(605) 996-7556
723 N Rowley St
Mitchell, SD
Services
Auto Parts

Napa Auto Parts
(605) 996-6643
816 N Main St
Mitchell, SD
Services
Auto Parts, Car Washes, Car Detailing

Larry's I 90 Svc
(605) 996-1042
1510 S Burr St
Mitchell, SD

Data Provided By:
Tma-Mitchell
(605) 996-1255
806 N Main St
Mitchell, SD

Data Provided By:
A and G Diesel Truck Repair
(605) 996-4137
123 E Spruce Street
Mitchell, SD
Services
Truck Parts

Trail King Industries Inc
(605) 996-3600
300 E Norway Avenue
Mitchell, SD
Services
Trailer Repair,Truck Parts

Advance Auto Parts
(605) 995-6253
500 E Havens Ave
Mitchell, SD

Data Provided By:
Top Shop
(605) 996-8508
724 N Duff St
Mitchell, SD

Data Provided By:
O'Reilly Auto Parts
(605) 996-0109
220 E Havens Ave
Mitchell, SD

Data Provided By:
Data Provided By:

Build With Bolt-On Horsepower, But Proceed With Caution

Stores, catalogs and trade shows are loaded with companies selling parts that enthusiasts can bolt onto their cars to add underhood power.


Page 1 of 2

Whether the speed equipment is old school hardware or electronic in nature, you can be sure it is designed to turn automobile engines into more efficient air pumps.

“Because the engine really is an air pump, I tell my customers one of the biggest things they can do is bolt on a different exhaust system,” says Dick Casar of Done Rite Automotive Performance in  (www.doneriteautomotive.com). Typically headers and dual exhausts will be installed on classic muscle cars, while newer cars will benefit from a 52-states-legal cat-back (catalytic converter back) exhaust system. Most cat-back systems are legal in all states.

Aftermarket headers are designed to give burnt gases exiting the engine a smoother flow route compared to factory-installed exhaust manifolds. Tight tuck models are available for cramped engine compartments. A long tube header kit with a two-inch diameter primary pipe and a pair of catalytic converters can run $1,000 to $2,000 (note: prices quoted in this article are ballpark prices at the counter with your markup).

Brand name systems are usually designed for direct fits on specific cars and can add 8 to 10 hp. Stainless steel hardware will eliminate rust, but mild steel hardware is stronger; your choice. Look for kits that have exhaust manifold studs with hexes on the end for easy installation with an Allen wrench. Before ordering your studs, double check how long you need them to be.

For about $400-$500 a performance style free-flowing exhaust system will include fat mandrel-bent pipes (usually 2-1/2-in. diameter) and low-restriction type mufflers for an increase of 15 to 20 hp. Due to emissions regulations, modern cars need to go with the cat-back option, which will give boosts in the 11-15 hp range for $1,200 to $1,500.

The critical fuel/air mixture that feeds the “air pump” its proper diet is another area where improvements can be made today, says Casar. “On your older carbureted cars, look for gains in the eight horsepower range after adding an aftermarket performance carburetor that will flow 650 cubic feet of air per minute through the engine. Or you can add bigger jets and get the carburetor pumping up to 750 cfm of air for roughly a 10-hp gain.”

According to Ed Casar – Dick’s son and partner at Done Rite Automotive Performance – carburetor companies haven’t been sleeping. Recently, they came out with models that incorporate new ways to atomize fuel. “They look the same as the old double pumper, but lasers are used to drill smaller holes and the manufacturers also have more surface control today.”

Ed continues, “Thanks to the air/fuel meters we have now, we can take a carbureted car, put it on our Super Flow dyno and tune the thing t...

Click here to read more from Engine Builder

Babcox Media • www.babcox.com
3550 Embassy Parkway
Akron, OH 44333
330-670-1234 • (FAX) 330-670-0874