Aftermarket Engines Sioux City IA

This page provides relevant content and local businesses that can help with your search for information on Aftermarket Engines. You will find informative articles about Aftermarket Engines, including "Build With Bolt-On Horsepower, But Proceed With Caution". Below you will also find local businesses that may provide the products or services you are looking for. Please scroll down to find the local resources in Sioux City, IA that can help answer your questions about Aftermarket Engines.

Dakotaland Autoglass Inc
(712) 233-1085
820 Pearl Street
Sioux City, IA
Fremont Tire Inc
(712) 258-7520
3324 N Us Highway 75
Sioux City, IA
Auto Parts,Service Stations,Truck Repair

Side Dump IND
(402) 494-6529
729 W 21st Street
South Sioux City, NE
Trailer Repair,Truck Parts

Frame Aligners Inc
(402) 494-3711
1509 Stable Drive
South Sioux City, NE
Alignment Repair,Truck Parts

Napa Auto Parts
(712) 252-6336
605 Wesley Pkwy
Sioux City, IA
Auto Parts, Car Washes, Car Detailing

Zenk Auto and Repair Inc
(712) 277-9068
2101 4th St
Sioux City, IA
Auto Parts,Service Stations,Truck Repair

Jim Hawk Truck Trailers Inc
(402) 494-8343
324 W 39th Street
South Sioux City, NE
Trailer Repair,Truck Parts

C and H Truck Parts
(402) 494-6866
569 Old Highway 20 West
South Sioux City, NE
Truck Parts

Sioux Plating CO Inc
(402) 494-2477
428 E 9th Street
South Sioux City, NE
Tires Tires Tires
(712) 258-7500
2620 Gordon Dr
Sioux City, IA
Auto Parts,Alignment Repair,Mufflers Repair,Service Stations,Truck Repair

Build With Bolt-On Horsepower, But Proceed With Caution

Stores, catalogs and trade shows are loaded with companies selling parts that enthusiasts can bolt onto their cars to add underhood power.

Page 1 of 2

Whether the speed equipment is old school hardware or electronic in nature, you can be sure it is designed to turn automobile engines into more efficient air pumps.

“Because the engine really is an air pump, I tell my customers one of the biggest things they can do is bolt on a different exhaust system,” says Dick Casar of Done Rite Automotive Performance in  ( Typically headers and dual exhausts will be installed on classic muscle cars, while newer cars will benefit from a 52-states-legal cat-back (catalytic converter back) exhaust system. Most cat-back systems are legal in all states.

Aftermarket headers are designed to give burnt gases exiting the engine a smoother flow route compared to factory-installed exhaust manifolds. Tight tuck models are available for cramped engine compartments. A long tube header kit with a two-inch diameter primary pipe and a pair of catalytic converters can run $1,000 to $2,000 (note: prices quoted in this article are ballpark prices at the counter with your markup).

Brand name systems are usually designed for direct fits on specific cars and can add 8 to 10 hp. Stainless steel hardware will eliminate rust, but mild steel hardware is stronger; your choice. Look for kits that have exhaust manifold studs with hexes on the end for easy installation with an Allen wrench. Before ordering your studs, double check how long you need them to be.

For about $400-$500 a performance style free-flowing exhaust system will include fat mandrel-bent pipes (usually 2-1/2-in. diameter) and low-restriction type mufflers for an increase of 15 to 20 hp. Due to emissions regulations, modern cars need to go with the cat-back option, which will give boosts in the 11-15 hp range for $1,200 to $1,500.

The critical fuel/air mixture that feeds the “air pump” its proper diet is another area where improvements can be made today, says Casar. “On your older carbureted cars, look for gains in the eight horsepower range after adding an aftermarket performance carburetor that will flow 650 cubic feet of air per minute through the engine. Or you can add bigger jets and get the carburetor pumping up to 750 cfm of air for roughly a 10-hp gain.”

According to Ed Casar – Dick’s son and partner at Done Rite Automotive Performance – carburetor companies haven’t been sleeping. Recently, they came out with models that incorporate new ways to atomize fuel. “They look the same as the old double pumper, but lasers are used to drill smaller holes and the manufacturers also have more surface control today.”

Ed continues, “Thanks to the air/fuel meters we have now, we can take a carbureted car, put it on our Super Flow dyno and tune the thing t...

Click here to read more from Engine Builder

Babcox Media •
3550 Embassy Parkway
Akron, OH 44333
330-670-1234 • (FAX) 330-670-0874