Bearings Cody WY

Looking for Bearings in Cody? We have compiled a list of businesses and services around Cody that should help you with your search. We hope this page helps you find Bearings in Cody.

L A Service
(307) 587-8464
2830 Big Horn Avenue
Cody, WY
Services
Auto Service & Repair, Brakes Service & Repair
Hours
Mon-Fri Weekdays

Wal-Mart Supercenter
(307) 587-0862
321 Yellowstone Ave
Cody, WY
Services
Car Washes, Car Detailing, Tire Shops

Carquest Auto Parts
(307) 587-2255
2013 Big Horn Ave
Cody, WY
Services
Auto Parts

Yellowstone Automotive
(307) 527-7464
553 14th Street
Cody, WY
Services
AC and Heating Repair,Radiator Repair,Transmission Repair

Shoshone Canyon Auto & Tire Co
(307) 587-2908
428 W Yellowstone Ave
Cody, WY
Services
Car Washes, Car Detailing, Tire Shops

Technical Cowboy Automotive
(307) 587-6968, 001-2004
901 - 16th Street
Cody, WY
Certifications
Blue Seal Certified
Membership Organizations
National Institute for Automotive Service Excellence (ASE)

Data Provided By:
Rimrock Tire Inc
(307) 587-6875
2603 Big Horn Ave
Cody, WY
Services
Car Washes, Car Detailing, Tire Shops

Napa Auto Parts
(307) 587-2253
1332 Beck Ave
Cody, WY
Services
Auto Parts, Car Washes, Car Detailing

OReilly Auto Parts
(307) 587-4737
320 Yellowstone Avenue
Cody, WY
Services
AC and Heating Repair,Clutch Repair

Joe's Auto
(307) 587-3248
513 Date St
Cody, WY

Data Provided By:
Data Provided By:

Back to Basics Bearings

Bearings are one of the most important parts inside an engine, so it’s important to understand their role in the overall operation of the engine, their design features, and how to install them properly. Engine bearings are a relatively inexpensive component compared to the cost of labor and many of the other parts that go into rebuilding an engine, but if one fails or causes a problem that results in a warranty claim, it can cost you plenty! So with that in mind, let’s review some of the basics about bearings.

Bearings actually have a variety of roles inside an engine, including:

Supporting the crankshaft and camshaft; Limiting the fore and aft movement of the crankshaft (this job belongs to the thrust bearing); Reducing friction; Lubricating the rotating shafts and connecting rods; Providing splash lubrication for the pistons, rings and cylinder walls (which also helps cool the pistons); Conducting heat away from the rotating parts; and Affecting how much oil pressure the engine develops at idle and higher rpms.

Basic design
Sleeve type bearings are used in most engines to support the crankshaft and camshaft. Most crankshaft main bearings are a two-piece (upper and lower) split shell design, while most cam bearings for pushrod engines are a one-piece full round design.

In overhead cam (OHC) engines, the cam bearings may be either type, or there may be no bearing inserts at all, i.e., the machined surface of the cam bores serve as the bearing surface for the cam(s).

Sleeve style wet bearings are used instead of ball bearings or roller bearings in most automotive applications because they are cheaper, lighter and are capable of supporting high loads. Even so, ball or roller bearings are sometimes used to support balance shafts in some engines, as well as the crankshaft in some motorcycle, marine and racing engines.

Though ball bearings and roller bearings are called "anti-friction" bearings because they spin easily and produce little drag, a rotating shaft supported on a film of oil inside a pressurized sleeve style bearing also spins with minimal resistance. The only drag on the shaft is that created by the shearing characteristics of the oil film. Also, the oil film helps spread the bearing load over a broader surface unlike a ball bearing or roller bearing, which concentrates the load at a single point or line.

At a microscopic level, oil molecules are like tiny ball bearings and glide easily past one another. That’s why oil feels slippery and makes such a good lubricant. And, the thinner the viscosity of the oil, the more easily it shears and the less friction and drag it creates. But, the oil must have a certain amount of viscosity so it can maintain film strength and not gush out of the bearing too quickly.

Temperature is also a factor to consider, too, because the hotter the oil gets the thinner it gets. If low viscosity oil is subjected to too much heat, it may not be able to maintain ad...

Click here to read more from Engine Builder

Babcox Media • www.babcox.com
3550 Embassy Parkway
Akron, OH 44333
330-670-1234 • (FAX) 330-670-0874