Bearings Tuscaloosa AL

Looking for Bearings in Tuscaloosa? We have compiled a list of businesses and services around Tuscaloosa that should help you with your search. We hope this page helps you find Bearings in Tuscaloosa.

David's Custom Exhaust?
(205) 345-4044
2917 15th St
Tuscaloosa, AL
Specialty
Exhaust Repair
Hours
Mon:8:00 am-5:00 pm
Tue:8:00 am-5:00 pm
Wed:8:00 am-5:00 pm
Thu:8:00 am-5:00 pm
Fri:8:00 am-5:00 pm
Sat:(Closed)
Sun:(Closed)
Payment
Cash, Credit Card

Norris A C Radiator and Service Center
(205) 759-8200
919 31st Street
Tuscaloosa, AL
Services
Radiator Repair

Bonner Body Shop
(205) 759-1246
1520 Queen City Avenue
Tuscaloosa, AL
Specialty
Paint & Body Work, Upholstery
Hours
Mon:7:30 am-5:30 pm
Tue:7:30 am-5:30 pm
Wed:7:30 am-5:30 pm
Thu:7:30 am-5:30 pm
Fri:7:30 am-5:30 pm
Sat:(Closed)
Sun:(Closed)
Payment
Cash, Check, Credit Card

Sammy Foster
(205) 752-9648
4100 69th Ave
Tuscaloosa, AL
 
Jacmac Tire Co
(205) 752-3501
2107 9th Street
Tuscaloosa, AL
Specialty
Tires/Wheels, Wheel Alignment
Hours
Mon:7:30 am-5:00 pm
Tue:7:30 am-5:00 pm
Wed:7:30 am-5:00 pm
Thu:7:30 am-5:00 pm
Fri:7:30 am-5:00 pm
Sat:(Closed)
Sun:(Closed)
Payment
Cash, Check, Credit Card

Masterbilt Trans By Kenny
(205) 345-1018
527 2nd Ave
Tuscaloosa, AL
 
Autozone
(205) 758-8351
3500 Greensboro Ave
Tuscaloosa, AL
Services
Auto Parts

Smalley' S Transmission Service
(205) 758-3700
1515 12th Ave
Tuscaloosa, AL
Specialty
Transmission
Hours
Mon:8:00 am-5:00 pm
Tue:8:00 am-5:00 pm
Wed:8:00 am-5:00 pm
Thu:8:00 am-5:00 pm
Fri:8:00 am-5:00 pm
Sat:(Closed)
Sun:(Closed)
Payment
Cash, Check, Credit Card

Logan Willie & Sons Art & Signs
(205) 339-1422
Highway 43
Tuscaloosa, AL
Services
Auto Body

Goodyear Tire Center
(205) 752-2524
2519 12th St
Tuscaloosa, AL
Services
Car Washes, Car Detailing, Tire Shops

Back to Basics Bearings

Bearings are one of the most important parts inside an engine, so it’s important to understand their role in the overall operation of the engine, their design features, and how to install them properly. Engine bearings are a relatively inexpensive component compared to the cost of labor and many of the other parts that go into rebuilding an engine, but if one fails or causes a problem that results in a warranty claim, it can cost you plenty! So with that in mind, let’s review some of the basics about bearings.

Bearings actually have a variety of roles inside an engine, including:

Supporting the crankshaft and camshaft; Limiting the fore and aft movement of the crankshaft (this job belongs to the thrust bearing); Reducing friction; Lubricating the rotating shafts and connecting rods; Providing splash lubrication for the pistons, rings and cylinder walls (which also helps cool the pistons); Conducting heat away from the rotating parts; and Affecting how much oil pressure the engine develops at idle and higher rpms.

Basic design
Sleeve type bearings are used in most engines to support the crankshaft and camshaft. Most crankshaft main bearings are a two-piece (upper and lower) split shell design, while most cam bearings for pushrod engines are a one-piece full round design.

In overhead cam (OHC) engines, the cam bearings may be either type, or there may be no bearing inserts at all, i.e., the machined surface of the cam bores serve as the bearing surface for the cam(s).

Sleeve style wet bearings are used instead of ball bearings or roller bearings in most automotive applications because they are cheaper, lighter and are capable of supporting high loads. Even so, ball or roller bearings are sometimes used to support balance shafts in some engines, as well as the crankshaft in some motorcycle, marine and racing engines.

Though ball bearings and roller bearings are called "anti-friction" bearings because they spin easily and produce little drag, a rotating shaft supported on a film of oil inside a pressurized sleeve style bearing also spins with minimal resistance. The only drag on the shaft is that created by the shearing characteristics of the oil film. Also, the oil film helps spread the bearing load over a broader surface unlike a ball bearing or roller bearing, which concentrates the load at a single point or line.

At a microscopic level, oil molecules are like tiny ball bearings and glide easily past one another. That’s why oil feels slippery and makes such a good lubricant. And, the thinner the viscosity of the oil, the more easily it shears and the less friction and drag it creates. But, the oil must have a certain amount of viscosity so it can maintain film strength and not gush out of the bearing too quickly.

Temperature is also a factor to consider, too, because the hotter the oil gets the thinner it gets. If low viscosity oil is subjected to too much heat, it may not be able to maintain ad...

Click here to read more from Engine Builder

Babcox Media • www.babcox.com
3550 Embassy Parkway
Akron, OH 44333
330-670-1234 • (FAX) 330-670-0874