Chevy 3.1L/191 Cam Bearing Bores Huntsville AL

Looking for Chevy 3.1L/191 Cam Bearing Bores in Huntsville? We have compiled a list of businesses and services around Huntsville that should help you with your search. We hope this page helps you find Chevy 3.1L/191 Cam Bearing Bores in Huntsville.

E & C Auto Repair
(256) 829-8996
14080A Highway 231 431 N
Hazel Green, AL
Hours
Monday 7:30 AM - 5:00 PM
Tuesday 7:30 AM - 5:00 PM
Wednesday 7:30 AM - 5:00 PM
Thursday 7:30 AM - 5:00 PM
Friday 7:30 AM - 5:00 PM
Saturday 8:00 AM - 2:00 PM
Sunday Closed
Memberships and Certifications
Certifications : ASE
Services
Air Conditioning/Heating, Alignment, Alternator, Battery, Belts & Hoses, Catalytic Converter, Clutch Cylinder, Cooling System, Diagnostics, Drive Belt, Electrical System, Exhaust Systems, Filters & Fluids, Fuel Injector, Fuel Pump, Fuel System, Head Gasket, Headlight/Headlamp, High Performance Service, Ignition, Inspection, Muffler, Oil Pan, Oil Pump, Oxygen Sensor, Parts, Radiator, Restoration Service, Shocks & Struts, Spark Plugs, Starter, Thermostat, Timing Belt, Tune-Up, Water Pump, Window M
Service Types and Repair
Acura, Aston Martin, Audi, Auto Clutch, Auto Drivetrain, Auto Engine, Auto Interior, Auto, Bentley, BMW, Buick, Cadillac, Chevrolet, Chrysler, Classic Car, Diesel Engine, Dodge, Emergency Auto, Exotic Car, Fiat, Ford, GMC, Honda, Hyundai, Infiniti, Isuzu, Jaguar, Jeep, Kia, Land Rover, Lexus, Lincoln, Lotus, Mazda, Mercedes Benz, Mitsubishi, Nissan, Oldsmobile, Pontiac, Porsche, RV/Bus, Saab, Saturn, Small Engine, Subaru, Suzuki, Toyota, Truck, Volkswagen, Volvo

Napa Auto Parts
(256) 539-7776
2602 Artie St Sw
Huntsville, AL
Services
Auto Parts, Car Washes, Car Detailing

Bentley Cadilac GMC
(256) 536-2475
2120 Drake Ave SW
Huntsville, AL
Specialty
Air Conditioning Repair, Brakes, Electrical Service, Emission Testing, Engine Repair, Exhaust Repair, Front End Repair, General Automotive Repair, Inspection & Diagnostic, Lubrication Service, Maintenance, Paint & Body Work, Tires/Wheels, Transmission, Upholstery, Wheel Alignment
Hours
Mon:7:00 am-6:00 pm
Tue:7:00 am-6:00 pm
Wed:7:00 am-6:00 pm
Thu:7:00 am-6:00 pm
Fri:7:00 am-6:00 pm
Sat:7:00 am-1:00 pm
Sun:(Closed)
Payment
Cash, Check, Credit Card

Ricks Transmission
(256) 489-0948
2919 Bob Wallace Southwest
Huntsville, AL
 
Hammond, Chong
(256) 539-7977
200 Jordan Ln NW
Huntsville, AL
 
Diehl Nissan-Infiniti-Mazda-Mitsubishi 3300 6Th Ave Sw
(256) 533-9291
Diehl Nissan-Infiniti-Mazda-Mitsubishi 3300 6Th Ave Sw
Huntsville, AL
 
Joe Harrisons Transmissions & Automotive
(256) 533-0101
109 8th Street Northwest
Huntsville, AL
 
Express Oil Change & Service Center?
(256) 721-0077
5700 Sanderson St NW
Huntsville, AL
Specialty
Lubrication Service
Hours
Mon:8:00 am-6:00 pm
Tue:8:00 am-6:00 pm
Wed:8:00 am-6:00 pm
Thu:8:00 am-6:00 pm
Fri:8:00 am-6:00 pm
Sat:7:30 am-5:00 pm
Sun:(Closed)
Payment
Cash, Check, Credit Card

Firestone Complete Auto Care Store
(256) 539-4118
2010 Bob Wallace Ave Sw
Huntsville, AL
Hours
M-F: 7:00am-7:00pm
Sa: 7:00am-6:00pm
Su: 8:00am-5:00pm

Advance Diesel Systems
(256) 534-3034
2411 Clinton Avenue West
Huntsville, AL
Services
Fuel Injection Repair

Chevy 3.1L/191 Cam Bearing Bores

Some of the later roller cam 3.1L blocks for the ’93-’94 Chevy VIN M are showing up with oversize cam bearing bores that appear to have been caused by spun cam bearings. If a new cam bearing is installed in a bore that has been damaged, it will spin in the block, cut off the oil to the cam, and cause an immediate failure.

Some of the later roller cam 3.1L blocks for the ’93-’94 Chevy VIN M are showing up with oversize cam bearing bores that appear to have been caused by spun cam bearings. If a new cam bearing is installed in a bore that has been damaged, it will spin in the block, cut off the oil to the cam, and cause an immediate failure.

Inspect the cam bores in all of the late 3.1L castings (10137093/ 10191737/ 24504089/ 24504150/ 10224227) very carefully, paying special attention to the #2 bore that seems to be the most prone to failure. If the cam bore is oversize, there are only two choices: 1) You can either knurl the O.D. of the cam bearing to get enough press fit, or 2) you can junk the block....

Click here to read more from Engine Builder

Babcox Media • www.babcox.com
3550 Embassy Parkway
Akron, OH 44333
330-670-1234 • (FAX) 330-670-0874