Drag Racing Cylinder Head Aberdeen SD
902 6th Avenue Southwest
Auto Air Conditioning & Heating Service & Repair, Auto Service & Repair, Auto Oil & Lube, Brakes Service & Repair, Mufflers & Exhaust Systems Service & Repair
Hoven Auto Repair Inc
2098 W Melgaard Rd
South Side Toyota Honda
1700 6th Ave SW
Schipke Auto Body
1220 S Highway 281
Crawford Trucks & Equipment, Inc.
3601 6th Ave SE
40548 131st Street
Auto Service & Repair, Auto Tire Shop Equipment & Supplies, Fuel Oils Wholesale
24 Hours a Day
American Express, MasterCard, Discover, VISA
Randys Auto Salvage
Auto Glass Repair,Truck Auto Body
Biegler's C & S Motorsports
1502 6th Ave SW
Inspection & Diagnostic, Lubrication Service, Maintenance
Mon:8:00 am-5:30 pm
Tue:8:00 am-5:30 pm
Wed:8:00 am-5:30 pm
Thu:8:00 am-5:30 pm
Fri:8:00 am-5:30 pm
Cash, Check, Credit Card
Gellings Auto Service
503 N Roosevelt Street
3204 U.S. 281
Air Conditioning Repair, Brakes, Electrical Service, Engine Repair, Front End Repair, Inspection & Diagnostic, Lubrication Service, Radiator Repair, Wheel Alignment
Mon:8:00 am-5:00 pm
Tue:8:00 am-5:00 pm
Wed:8:00 am-5:00 pm
Thu:8:00 am-5:00 pm
Fri:8:00 am-5:00 pm
Drag Racing Cylinder Head Selection
By Brendan Baker
When you talk about performance heads for drag racing - or any other performance application for that matter - the best heads aren't necessarily the ones with the biggest cubic feet per minute (CFM) numbers. Experts say that the key ingredient is high velocity matched with good flow. But the high flow numbers may blind your customers from seeing the whole picture, so it is up to you to explain.
Some cylinder head experts compare flow numbers to horsepower numbers on a dyno - but guess what? They're not all equal. So if you see one head with extremely high CFM numbers there are a couple of guesses what may be going on. One cylinder head expert says that the general enthusiast/racer doesn't know if the numbers are bogus, all he sees is a big number and that's what he wants.
Larger engines need larger volume ports. And today there are many aftermarket cylinder heads to choose from with larger ports. But before these heads were available, drag racers didn't have many options as to what size heads to use. Most racers would look for the biggest stock head available and adapt it to their application. Yet one of the biggest problems with using stock heads is that you're stuck with the port locations and the thickness of the casting, so you can't get too radical.
Some aftermarket heads have features such as raised runners and relocated ports to improve airflow. Today's aftermarket "as cast" cylinder heads with unmachined ports often flow better than stock heads that have been ported. And "bare" aftermarket heads are available to allow CNC porting to create almost any shape port you want.
Cylinder head specialist Darin Morgan says that with all the aftermarket heads available choosing a cylinder head today is a difficult task. Unfortunately, a bad choice can cost thousands of dollars in wasted time, says Morgan, and a bad head choice may go unnoticed without ever showcasing how good your engine could have been.
So with all the heads on the market, how do you make the right choice? Morgan says it's a complex issue with no simple answer.
"I wish I could lay out some quick and easy mathematical equations or some simple guidelines to help, but there simply aren't any," says Morgan. "It's a complex issue, which is why so many people have trouble. The best way to grasp what's most important is to use what I consider the five most important variables used to tune the induction system:
Individual instantaneous velocities;
Shape/design (maximize a homogeneous velocity profile over the entire port and at the same time promote efficient flow);
Rate of velocity change; and
Airflow. Morgan says that if you follow his five variables you'll soon find the most important rules of designing an induction system are: Velocity, Velocity, Shape, Velocity and, finally, Airflow.
We then talked to Curtis Boggs at Race Flow Development (RFD), who says his company takes a bare casting and comes up with its o...
Click here to read more from Engine Builder