Drag Racing Cylinder Head Rutland VT

Looking for Drag Racing Cylinder Head in Rutland? We have compiled a list of businesses and services around Rutland that should help you with your search. We hope this page helps you find Drag Racing Cylinder Head in Rutland.

Carquest Auto Parts
(802) 773-2788
252 Randbury Road
Rutland, VT
Services
Clutch Repair,Engine Repair

Midas Auto Service Experts
(802) 775-2948
Woodstock Ave
Rutland, VT
Services
Car Washes, Car Detailing, Mufflers Repair

Rutland Motorcars Llc 200 West Street
(802) 747-7171
Rutland Motorcars Llc 200 West Street
Rutland, VT
 
Adirondack Tire Centers
(802) 775-1944
55 Strongs Ave
Rutland, VT
Services
Car Washes, Car Detailing, Tire Shops

Design Graphics
(802) 775-5233
225 S Main St
Rutland, VT
Services
Auto Body

Turners Transmissions
(802) 773-7619
Rutland, VT
 
Sears Roebuck and Co
(802) 770-3095
82 Diamond Run Pl
Rutland, VT
Services
Car Washes, Car Detailing, Tire Shops

Jiffy Lube
(802) 775-9231
279 S Main St
Rutland, VT
Services
Oil Change and Lube, Automotive Transmission

Goss Tire Company
(802) 773-3360
133 Strongs Ave
Rutland, VT
Services
Car Washes, Car Detailing, Tire Shops

Ray Beane Tire & Service Center
(802) 773-2741
140 S Main St
Rutland, VT
Services
Car Washes, Car Detailing, Tire Shops

Drag Racing Cylinder Head Selection

Brendan Baker

When you talk about performance heads for drag racing - or any other performance application for that matter - the best heads aren't necessarily the ones with the biggest cubic feet per minute (CFM) numbers. Experts say that the key ingredient is high velocity matched with good flow. But the high flow numbers may blind your customers from seeing the whole picture, so it is up to you to explain.

Some cylinder head experts compare flow numbers to horsepower numbers on a dyno - but guess what? They're not all equal. So if you see one head with extremely high CFM numbers there are a couple of guesses what may be going on. One cylinder head expert says that the general enthusiast/racer doesn't know if the numbers are bogus, all he sees is a big number and that's what he wants.

Larger engines need larger volume ports. And today there are many aftermarket cylinder heads to choose from with larger ports. But before these heads were available, drag racers didn't have many options as to what size heads to use. Most racers would look for the biggest stock head available and adapt it to their application. Yet one of the biggest problems with using stock heads is that you're stuck with the port locations and the thickness of the casting, so you can't get too radical.

Some aftermarket heads have features such as raised runners and relocated ports to improve airflow. Today's aftermarket "as cast" cylinder heads with unmachined ports often flow better than stock heads that have been ported. And "bare" aftermarket heads are available to allow CNC porting to create almost any shape port you want.

Cylinder head specialist Darin Morgan says that with all the aftermarket heads available choosing a cylinder head today is a difficult task. Unfortunately, a bad choice can cost thousands of dollars in wasted time, says Morgan, and a bad head choice may go unnoticed without ever showcasing how good your engine could have been.

So with all the heads on the market, how do you make the right choice? Morgan says it's a complex issue with no simple answer.

"I wish I could lay out some quick and easy mathematical equations or some simple guidelines to help, but there simply aren't any," says Morgan. "It's a complex issue, which is why so many people have trouble. The best way to grasp what's most important is to use what I consider the five most important variables used to tune the induction system:

Average velocity;

Individual instantaneous velocities;

Shape/design (maximize a homogeneous velocity profile over the entire port and at the same time promote efficient flow);

Rate of velocity change; and

Airflow. Morgan says that if you follow his five variables you'll soon find the most important rules of designing an induction system are: Velocity, Velocity, Shape, Velocity and, finally, Airflow.

We then talked to Curtis Boggs at Race Flow Development (RFD), who says his company takes a bare casting and comes up with its o...

Click here to read more from Engine Builder

Babcox Media • www.babcox.com
3550 Embassy Parkway
Akron, OH 44333
330-670-1234 • (FAX) 330-670-0874